| MOBILE |
| Mobile module |
4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps |
| Status |
Signal strength (RSSI), SINR, RSRP, RSRQ, EC, IP Address, DNS, ICCID, IMEI, IMSI, RSCP Bytes sent/received |
| Bridge |
Direct connection (bridge) between mobile ISP and device on LAN |
| Passthrough |
Router assigns its mobile WAN IP address to another device on LAN |
| APN |
Auto APN |
| SMS |
Customized |
| Multiple PDN (optional) |
Possibility to use different PDNs for multiple network access and services |
| WIRELESS |
| Wireless mode |
IEEE 802.11b/g/n, Access Point (AP), Station (STA, Client) |
| WiFi |
WPA2-Enterprise (with external/internal Radius server), WPA2-PSK, WPA-PSK, WEP, MAC Filter |
| WiFi security |
WPA2-Enterprise - PEAP, TLS, TTLS, AES-CCMP, TKIP, Auto Cipher modes, Client separation |
| SSID |
SSID stealth mode and access control based on MAC address |
| WiFi users |
Up to 30 simultaneous connections |
| Wireless Hotspot |
Captive portal (Hotspot), built in customizable landing page |
| ETHERNET |
| WAN |
1 x WAN port (can be configured to LAN) 10/100 Mbps, comply IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX |
| LAN |
1 x LAN port, 10/100 Mbps, comply IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX |
| NETWORK |
| Routing |
Static routing, Dynamic routing |
| Network protocols |
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, TLS, ARP, PPP, PPPoE, UPnP, SSH, DHCP, Telnet, MQTT |
| VoIP passthrough support |
SIP-alg protocol NAT helpers |
| Connection monitoring |
Ping Reboot, Periodic Reboot, LCP and ICMP for link inspection |
| Firewall |
Port forward, traffic rules, custom rules, Domain filter, Keyword filter |
| DHCP |
Static and dynamic IP allocation |
| QoS |
Traffic priority queuing by source/destination, service, protocol or port |
| DMZ |
External network node can access only what is exposed in the DMZ, while the rest of the organization's network is firewalled |
| DDNS |
Support DDNS tool |
| Network backup |
Mobile, Wired and WiFi WAN options, each of which can be used as backup, using automatic Failover |
| Load balancing |
Balance your internet traffic over multiple WAN connections |
| SECURITY |
| Authentication |
Pre-shared key, digital certificates, X.509 certificates |
| Firewall |
Pre-configured firewall rules can be enabled via web-ui, unlimited firewall configuration via CLI; DMZ; NAT |
| WiFi security |
WPA2-Enterprise – PEAP, EAP-TLS, TLS, TTLS. AES-CCMP, TKIP, Auto Cipher modes, Client separation |
| WEB filter |
Blacklist for blocking out unwanted websites, whitelist for specifying allowed sites only |
| Access control |
Flexible access control of TCP, UDP, ICMP packets, MAC address filter |
| VPN |
| Mode |
Client service |
| Protocols |
GRE, PPTP, L2TP, IPsec, EOIP, N2N, OpenVPN |
| LOCATION TRACKING (optional) |
| GNSS |
GPS, BEIDOU, GPS, BEIDOU, GLONASS |
| Coordinates |
GNSS coordinates via WebUI, RMS |
| NMEA |
NMEA 0183 |
| Location Based Service |
Location without using GPS, get approximate location based on mobile tower |
| Device ID |
location data sending with ID to Identify it come from which device |
| SERIAL |
| RS232/RS485 |
3 pin industrial socket, 300-115200 baud rate |
| Serial functions |
Serial over IP, Serial to Ethernet, DTU, Modem, Modbus gateway |
| Transparent transmission |
Mode: TCP Server/Client, UDP Server/Client, RealCom, UDP Range, UDP Multicast, Pair Master/Slave |
| MODBUS |
| Support |
Modbus RTU Master/Slave, Modbus TCP Master/Slave, Modbus RTU to Modbus TCP, Modbus TCP to Modbus RTU transfer |
| MODBUS TCP SLAVE |
| ID range |
1-255 |
| Allow Remote Access |
Allow access through WAN |
| MODBUS TCP MASTER |
| Supported functions |
01, 02, 03, 04, 05, 06, 15, 16 |
| Supported data formats |
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit float (Big endian, Big endian with byte-swapped, Little endian, Little endian with byte-swapped) |
| MODBUS RTU MASTER (RS232) |
| Supported baud rates |
From 300 to 115200 |
| Supported functions |
01, 02, 03, 04, 05 (only for alarms), 06 (only for alarms), 15 (only for alarms), 16 (only for alarms) |
| Number of data bits |
From 5 to 8 |
| Number of stop bits |
1 or 2 |
| Parity |
None, Even, Odd |
| Flow |
None, RTS/CTS, Xon/Xoff |
| Duplex |
Full duplex |
| MODBUS RTU MASTER (RS485) |
| Supported baud rates |
From 300 to 115200 |
| Supported functions |
01, 02, 03, 04, 05 (only for alarms), 06 (only for alarms), 15 (only for alarms), 16 (only for alarms) |
| Number of data bits |
8 |
| Number of stop bits |
1 |
| Parity |
None, Even, Odd |
| Flow |
None, Xon/Xoff |
| Duplex |
Half duplex |
| MODBUS DATA TO SERVER |
| Protocol |
MQTT |
| MQTT GATEWAY |
| MQTT gateway |
Allows sending commands and receiving data from Modbus Master through MQTT broker |
| MONITORING & MANAGEMENT |
| WEB UI |
HTTP/HTTPS, status, configuration, FW update, troubleshoot, event log, system log, kernel log |
| FOTA |
Firmware update from Cloud Platform(M2M Platform, Remote Management System), automatic notification |
| MQTT |
MQTT Broker, MQTT publisher |
| JSON-RPC |
Management API over HTTP/HTTPS, Customized |
| MODBUS |
MODBUS TCP status/control |
| RMS |
Remote Management System (RMS) |
| IoT PLATFORMS |
| Cloud of Things |
Allows monitoring of: Device data, Mobile data, Network info, Availability |
| ThingWorx |
Allows monitoring of: WAN Type, WAN IP Mobile Operator Name, Mobile Signal Strength, Mobile Network Type |
| Cumulocity |
Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP |
| SYSTEM CHARACTERISTICS |
| CPU |
560 MHz |
| RAM |
128 MB |
| FLASH memory |
16 MB |
| FIRMWARE / CONFIGURATION |
| WEB UI |
Update FW from file, configuration profiles, configuration backup, restore point |
| FOTA |
Update FW/configuration from Cloud Platform(M2M Platform, Remote Management System) |
| RMS |
Update FW/configuration for multiple devices |
| Keep settings |
Update FW without losing current configuration |
| FIRMWARE CUSTOMIZATION |
| Operating system |
LEDE (OpenWrt based Linux OS) |
| Supported languages |
Busybox shell, Lua, C, C++ |
| Development tools |
SDK package with built environment provided |
| POWER |
| Connector |
DC 2 Pin Industrial Socket Power (support multiple plug standard and USB plug) |
| Input voltage range |
7.5 – 32 V DC (2 pin industrial socket), reverse polarity protection, surge protection |
| Power consumption |
< 3 W |
| PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTONS, SIM) |
| Ethernet |
2 x RJ45 ports, 10/100 Mbps |
| Serial |
1 x RS232/RS485, 3 pin industrial socket |
| Status LEDs |
1 x connection strength & status LEDs, 1 x WAN status LED, 1 x LAN status LED, 1 x Power LED, 1 x WiFi LED, 1 x SYS LED |
| SIM |
1 x SIM slot (Mini SIM – 2FF, 25mm x 15mm), 1.8 V/3 V, external SIM holder |
| Power |
2 Pin DC connector |
| Antennas |
1 x SMA for Mobile, 1 x SMA for WiFi antenna connectors |
| Reset |
Reset/restore to default button |
| PHYSICAL SPECIFICATION |
| Casing material |
Metal housing |
| Dimensions |
102 x 100 x 41 mm (L x W x H) |
| Weight |
355 g |
| Mounting options |
Desktop and DIN rail mounting slots |
| OPERATING ENVIRONMENT |
| Operating temperature |
-30 °C to 70 °C |
| Operating humidity |
<95% non-condensing |
| Ingress Protection Rating |
IP41 |
